BP6.Com

I sort of suspect that the lin lin will fall short. If you review the mods described for the varied slotket revisions. I think that the differences in the jump from fc-pga support to fc-pga2 on the varied rev's is a pretty good reason for lin lin to put the caveat on the box label 'may not support a...

A good source of information . They describe numerous levels of implementation for support of FC-pga and FC-PGA2 support with respect to various slotkets and of course your board . Mods for FC-PGA2 are significant. If I had the time and inclination,(and desire) get hold of a lin lin and probe for th...

My primary work system is an IBM Thinkpad. Would have it no other way. They are super.
For home I build what I need, ( and what I don''t need ) .

Try comparing your old kernel config to your current . site http://www.e-infomax.com/ipmasq/howto/c-html/ipmasq-compiling3.1.html an excellent source for checking out your masq setup . Shows 2.4 kernel options ...I'm running 2.6 kernel now and have no local reference data for you. Used to run same o...

trueg wrote:Instead of using two socket adapters, would it make sense that I could simply modify my ZM6 (as seen here.. http://www.3feetunder.com/krick/370mod/ ) to accept a FC-PGA and then use a lin lin to make it FC-PGA2 compatible?

Sounds only natural to me .

Yogi, it sounds like you made some significant progress . I tried to perform some mods to the lin lin (adds and deletes as best I could understand from the docs in this site) in hopes to get it going in "uni" mode but stopped short of socket mods on the bp6 itself. The net of what I was trying to do...

The NEO mods are also listed in an updated page for the BP6 at http://www.friendtech.com/NeoBP6Updated-3.htm Does anybody know the purpose of shorting diodes D1 and D2? I've begun looking at the LIN-LIN for modding requirements and trying to figure out if I can put a couple turns of wire wrap on the...

I did the same thing that you did with lin lin...no no go go . Even though I knew of the neo and p3 mods ( see http://www.bp6.com/board/kb.php?mode=article&k=9 ) . I didn't want to commit the bp6 board wiring mod until I can get the router moved off my linux box. I'm working on a bh6 substitute , on...

Hi Bardos, I see you probed with the jumpers on. In this state you should see continuity from the VSS (there are a few of these, a beeping DMM will help find the right one) and your jumpered VID1 for example... You'll find A1, A4, A7, B1 (VIDx passthru pins) on the socket side where your CPU will fe...

bardos, when you jumper a1-2, a4-5 and a7-8 you are allowing the VIDx signals to pass from the CPU for autodetect....reason you saw a 1.30 when you boot is that you didn't pass VID3 for autodetect, you floated it. I probed my lin lin today... A1, A4, A7, B1, B4, B7 allow the passthru of the adjacent...

Thanks, I was grasping for some hope re voltages. If its any consolation, I have similar story that goes back to the old bp6 forum. (bios voltages ). Mine also is a rev 1.0 Mostly stable for the last 18 months, until I tinker with the clocks. I've had bios voltages only for about the first week of o...

I've made up this little pic so's not to get messed up with the doc on the back of the LinLin box. I believe that it's acurate, based on my interpretation of the JPx comments on the box. I'm assuming JP1 position based on the pin 1/2/3 references. In case you find news referencing the JP #'s I can't...

Glad to hear things are better. Do you get your voltages back on the bios panel??
I just replaced EC10 (100uF) with 1000 uF/6.3 and hasn't fixed my bios voltages...but my mouse works again.

Thanks onelegis Appreciate the jumper info , but curious about the cryptic text near the end of your post . I've got a LinLin working with C1200 on a MSI slotket in a BH6 (slot1) and am purchasing 2 for my BP6 to try dual coppermine Piii. The lin lin makes the Powerleap look like a rather pricy solu...

Hi, I have exactly the same problem. I bought my (also V1.0) bp6 last summer and after 3 weeks, I noticed that the bios presentation area where temps and voltages are available would sometimes show as N/A. This didn't last long, after a couple more days these panel areas disappeared altogether. I be...

Mine started as a uni- with winME, added OS/2 and PQMagic Bootmanager, then smp'd and installed RH7.3. All were managed via PQBootmgr. When I installed xp , it installed XP boot mgr on my winME drive C partition. Not a problem, re-activated PQBootmgr and everything still available. Same should be tr...

Thanks Derek. I installed bp6ru128 plus drivers for winME . Linux and winME still happy. (bios was from another site, mentioned elsewhere in this forum...its hpt366 1.28 code with RU and no PIII mods. Anyway, I installed xp today and found out quicky why so much fuss over the highpoint controller. A...

Re the ROBY2 RU, I run RU/hpt1.22 and use the hpt controller. (I moved a drive there for a performance test and was so happy I left it there) . Has ROBY 2 code got good reviews from celeron users?